Hsd 32 Compressor Manual
KAESER rotary screw compressors with SIGMA FREQUENCY CONTROL. Final exam study guide for history 1301. Is used (electricity, gas, fuel oil). ASD to HSD series rotary screw compres. Tolerance: ± 3 dB(A); ***) At high fan speed. 32 www.kaeser.com.
You need the compressed air, it is used as a bearing purge. Also, if you leave tool holders in there too long, they will get stuck, they must be exercised.Thank u sir for the reply ur suggestions always helpful. Sir last 4 month i am using the router without air. Will it harm the spindle? Or now just i start using compressed air and it will be ok.
Another question is the manual tool release button light on the spindle is off. When i noticed i connect the air and press the button to release its working but the light still off. Unlike my brother, I have an atc HSD spindle. It does have a minimum cfm rating on it but I've accidentally had it running with lower cfm and never an issue until pressure is low enough that the tool doesn't drop. Still, I'd hook it up to a little one at least as a $50 compressor is cheaper than a $5k+ spindleYes brother ur write. From today i will attach a compressor.
But my worries is their is any harm to the spindle? The issue with manual tool release button light is due to the air because iam not using air so is their is dust inside? Or it just the button bulb is went out. The green light is just a lamp.
They did not use an LED, they used an actual lamp, it burns out all the time. Do not worry about the light not working. It has no meaning other than that the bulb burned out. Did you do damage? Maybe a little, it is still working, that's good. There's nothing you can do but use it until it does not work, then get it rebuilt. Perhaps it will last a very long time.
I have seen people do far worse and have their spindles survive (water in the air lines is particularly terrible!). Hello sir how are u? Hmm a question is in my mind and i think u are the best to ask. A friend have a cnc router it 1.5 x 3 meters.
Xyz all exis 400 watts delta servo motors. Fixed with shimpo japan reducer gear on y and x exis. Hsd 929 atc spindle the weight is about 27 kg. The 400 watts z exis motor enough to carry the spindle weight and work. Question is the 400 watts servo motors enough power to work? Like cutting wood mdf 3d carving cutting aluminum. Second is z exis when moving the spindle up make zzummmmm zummm sound.
Is it normal? The machine is working from 4 months.
We also check the temprature of the all exis servo motors after working about 4 hours with an ir temprature gun. X, y 40 celsius and z 45 Celsius. Kindly give ur suggestion Thank u.
Asd 32 Compressor Manual Pdf
. More volume flow on less space For our HSD series, we integrated two compressors in a single enclosure. Both units are fully equipped with 1:1 direct drive, SIGMA CONTROL controller and cooling system. This series offers these technical data:.
Pressure: 8.5, 12 or 15 bar. Flow rate: 10.1 – 89 m³/min You can order HSD systems with or without speed-controlled drive. Due to the high flow rates, they are very well suited for demand-intensive applications in the automotive sector or steel industry. Your advantages. Versatility with minimal space requirements: Two small compressors in a single enclosure save much space when compared to a single compressor unit with corresponding output capacity.
This system optimally adapts to different demand situations, minimising idle times and increasing efficiency. Double dependability: Each compressor unit can be operated completely independently.
Asd 32 Compressor Manual
In the event of a unit failure, you still have 50% of your flow rate. Exceptional efficiency: Furthermore, we already use IE4 motors in HSD models and therefore provide you with even further energy savings. Standard version Model HSD 662 HSD 722 HSD 782 Working pressure bar 7.5 10 13 7.5 10 13 7.5 10 13 Flow rate Complete system at working pressure m³/min 66.4 54.44 43.72 72.4 59.48 47.87 78.4 65.31 53.07 Max. Positive pressure bar 8.5 12 15 8.5 12 15 8.5 12 15 Nominal motor output kW 360 400 450 Dimensions W x D x H mm 3,570 x 2,145 x 2,350 3,570 x 2,145 x 2,350 3,570 x 2,145 x 2,350 Compressed air connection DN150 PN16 DIN DN150 PN16 DIN DN150 PN16 DIN Sound pressure level dB(A) 71 72 72 Weight kg 8,100 7,481 7,027 8,500 8,202 7,262 8,600 8,434 7,815 Model HSD 842 Working pressure bar 7.5 10 13 Flow rate Complete system at working pressure m³/min 84.4 71.15 58.27 Max.
Positive pressure bar 8.5 12 15 Nominal motor output kW 500 Dimensions W x D x H mm 3,570 x 2,145 x 2,350 Compressed air connection DN150 PN16 DIN Sound pressure level dB(A) 73 Weight kg 8,700 8,666 8,368 SFC version Model HSD 662 SFC HSD 782 SFC HSD 842 SFC Working pressure bar 7.5 10 7.5 10 13 7.5 10 13 Flow rate Complete system at working pressure m³/min 10.4 - 66.32 8.5 - 57.47 11.9 - 77.83 10 - 65.47 8 - 55.78 11.9 - 87.33 10 - 74.41 8 - 63.44 Max. Positive pressure bar 8.5 12 8.5 12 15 8.5 12 15 Nominal motor output kW 382 410 515 Dimensions W x D x H mm 4,370 x 2,145 x 2,350 4,370 x 2,145 x 2,350 4,370 x 2,145 x 2,350 Compressed air connection DN150 PN16 DIN DN150 PN16 DIN DN150 PN16 DIN Sound pressure level dB(A) 73 74 75 Weight kg 9,100 8,967 9,600 9,113 8,980 10,100 9,934 9,315.